Marathon Sprint Series Instrukcje Operacyjne Pobierz pdf (Strona 19)

Safety Instructions

Once the drive has been installed, the person responsible for

installation has to issue an EU Conformity Declaration for the

door system in accordance with Machine Directive 98/37/EG as

well as fitting the CE seal and the rating plate.

This also applies to doors installed for private purposes and in

cases where the drive has been retrofitted to a manual door.

These Instructions as well as the drive's Installation and

Operating Instructions should be kept by the user for reference

purposes.

The force setting is relevant to the system's safety and must

therefore be carried out with due care and attention. An exces-

sively high force setting can injure people and/or animals and

damage property.

Select as low a force setting as possible to ensure that obstacles

are identified in a fast, safe manner.

Risk of sudden closing or opening!

When the emergency release is actuated, the door might

suddenly be opened or closed, due to a damaged spring or

incorrect balance weight. This might damage or even destroy

the drive unit.

Setting door OPEN + CLOSED final

travel positions

While adjusting the settings, open and close the gate manually.

Do not operate it with the engaged drive system.

The distance over which the drive mechanism moves the door can be

increased/reduced by using the cut-out buffer (V + H).

Check that the door opens and closes completely. If it does not, its travel

must be adjusted.

Door CLOSED final travel position

• Release the trolley. Pull the emergency release rope (N) once. It

must be possible to slide the trolley back and forth by hand.

• Close the door by hand.

• Release the switch trigger (V) and slide it towards the trolley until it

triggers the limit switch. Secure the switch trigger (V) with screws in

this position.

Door OPEN final travel position

• Open the door by hand.

• Release the switch trigger (H) and slide it towards the trolley until it

triggers the limit switch. Secure the switch trigger (H) with screws in

this position.

• Close the door by hand.

• Lock the trolley (1):

Pull the emergency release rope (N) once. Move the trolley by hand a

little bit forward until the chain wheel engages with a loud clicking

sound.

Teaching in drive

Whenever the door “opens” or “closes”, the control unit automatically reads

in the force required and memorises it when the end position is reached.

• Plug in power plug

The first movement of the drive after the power is connection

must be “door OPEN”. If this is not the case, exchange the wires

to terminals 3+ 4 (sprint/duo) or terminals 12 + 13 (marathon).

• Press the push-button (1). The door is opened to limit position

"door OPEN".

• Close gate, press button (1).

Reset the control unit

• Carry out control reset in accordance with the procedure for the

given drive type. See 'Operation / Handling' section.

Carry out following procedure twice:

• Press push-button (1) once

Door opens as far as cut-off buffer (H)

• Lamp (2) starts to flash

• Press push-button (1) once

Door closes as far as cut-off buffer (V)

• Lamp (2) starts to flash

When all force values are read and saved, the lamp (2) ceases flashing.

The operator has been 'taught' successfully!

Checking the limit positions for door

OPEN + CLOSED

The trolley of the drive system can be extended or shortened by means of

the switch triggers.

Check whether the door is opening and closing properly. If this is not the

case, adjust the trolley.

• Actuate the control device (e.g. push-button, remote control device,

etc.) once.

The door is opened.

If it fails to reach the desired limit positions for door OPEN + CLOSED,

readjust the limit positions. For detailed instructions, see chapter “Adjusting

door OPEN + CLOSED settings”.

Commissioning

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 34 35

Komentarze do niniejszej Instrukcji

Brak uwag

Marathon Sprint Series Instrukcje Operacyjne Strona 19

Komentarze do niniejszej Instrukcji